Остання редакція: 2025-05-30
Анотація
Анотація
У роботі представлено огляд сучасних досліджень щодо впливу локальних мікроструктурних неоднорідностей на пластичність листових металевих матеріалів. Розглянуто основні типи неоднорідностей — зони без преципітатів, текстурна анізотропія, фазова неоднорідність та залишкові напруження — і проаналізовано механізми формування «слабких» зон. Узагальнено експериментальні дані та встановлено величину впливу неоднорідностей на локальну граничну пластичну деформацію.
Abstract
The paper presents a review of modern research on the influence of local microstructural inhomogeneities on the plasticity of sheet metal materials. The main types of inhomogeneities are considered - zones without precipitates, textural anisotropy, phase inhomogeneity and residual stresses - and the mechanisms of formation of "weak" zones are analyzed. Experimental data are summarized and the magnitude of the influence of inhomogeneities on local ultimate plastic deformation is established.
Ключові слова
Посилання
1. Uchic M. D., Dimiduk D. M., Florando J. N., Nix W. D. Sample dimensions influence strength and crystal plasticity // Science. — 2004. — Vol. 305. — P. 986–989. https://doi.org/10.1126/science.1098993
2. Сивак Р.І., Матвійчук В.А., Грушко О.В. Немонотонна пластична деформація в процесах обробки металів тиском. – Вінниця: ВНАУ, 2022. – 202 с.
3. Esmaeili S., Lloyd D. J., Poole W. J. Modeling the evolution of precipitates during aging of Al–Mg–Si alloys // Acta Materialia. — 2003. — Vol. 51, № 17. — P. 5565–5578. https://doi.org/10.1016/S1359-6454(03)00426-6
4. Pohl M., Starke P., Eggeler G. Texture and anisotropy of plastic properties in aluminum alloys // Materials Science Forum. — 1991. — Vol. 157–162. — P. 887–892. https://doi.org/10.4028/www.scientific.net/MSF.157-162.887
5. Kahn H., Yao Y. L., Anderson R. Strain localization in dual-phase steels // Scripta Materialia. — 2001. — Vol. 45, № 6. — P. 653–660. https://doi.org/10.1016/S1359-6462(01)01105-5
6. Jin X., Edwards P. D., Khan T. Mechanical response of friction stir spot welded aluminum alloys under tension // Journal of Materials Processing Technology. — 2022. — Vol. 302. — P. 117486. https://doi.org/10.1016/j.jmatprotec.2021.117486
7. Chen Y. C., Nakata K. Effect of welding parameters on mechanical properties and microstructure of aluminum alloy 6061-T6 joined by friction stir welding // Materials & Design. — 2009. — Vol. 30, № 9. — P. 3363–3369. https://doi.org/10.1016/j.matdes.2008.07.063
8. Bellón B., Haouala S., LLorca J. An analysis of the influence of precipitate type on mechanical behavior of Al–Cu alloys by means of micropillar compression tests // Acta Materialia. — 2020. — Vol. 200. — P. 233–245. https://doi.org/10.1016/j.actamat.2020.08.039
9. Zubair M., Hegadekatte V., Zaefferer S. Stochastic modeling of flow behavior in heterogeneously structured metals // Computational Materials Science. — 2019. — Vol. 167. — P. 178–186. https://doi.org/10.1016/j.commatsci.2019.05.009